Skip to content
SATER — Electronics & appliance repair

Electrolux and AEG Appliance Repair in Riga — SATER

SATER service centre has been repairing Electrolux and AEG household appliances in Riga for over 30 years — since 1993, when our workshop grew out of Workshop No. 2 of the Soviet-era Elektrons factory. Over that time we have accumulated deep experience with SteamBake and SteamCrisp series ovens, induction cooktop IGBT modules, AEG Gourmet built-in microwaves, and Electrolux UltimateTaste coffee machines. Electrolux and AEG are effectively one group, and most platforms are shared: electronic control boards, thermocouples, steam generators, and induction power modules are interchangeable within the product line. This means one experienced technician can service both brands by understanding the underlying platform architecture. We work at component level: we resolder relays on oven control boards, replace IGBT transistors in induction hobs, clean and restore SteamBake steam generators, swap thermocouples with precise temperature calibration, and replace cracked ceramic glass on cooktops. All work is carried out at our service centre at Silmacu iela 6, Riga. Before starting any repair we agree on a cost estimate — no part is replaced without your approval. All repairs come with a 3-month warranty. If a repair is not cost-effective, we will tell you honestly and return the appliance with no obligation. Call +371 67377002 and bring your appliance in person — we are open weekdays and Saturdays from 9:00 to 16:00.

On-site diagnostics3-month warranty
+371 29 547 002WhatsApp

Popular models we repair

  • Electrolux SteamBake ovens (EOD6P, EOF6P)
  • AEG SteamBake / SteamCrisp ovens
  • Electrolux EHI induction cooktops
  • AEG MaxiSense induction cooktops
  • Electrolux UltimateTaste coffee machines
  • Electrolux PureF9 vacuum cleaners
  • AEG Gourmet built-in microwaves

Common problems we fix

  • SteamBake steam generator calcification — no steam or weak steam output, oven overheats
  • Induction IGBT module failure — zone clicks but does not heat
  • Oven thermocouple drift — temperature does not match the setting, baked goods burn or undercook
  • AEG pyrolysis door lock mechanism stuck — door will not open after self-cleaning cycle
  • Cracked ceramic cooktop glass replacement
  • Range hood electronic speed controller failure — fan does not switch speeds or runs on one speed only
  • Coffee machine water pump weak or no pressure — pump wear or valve blockage
  • Oven control board relay stuck — heating element will not turn off
  • Microwave door switch failure — unit starts and stops randomly

Detailed problem guides

Pick a symptom — we walk through the causes, what you can check yourself, and when to bring it in.

Electrolux and AEG oven electronics: SteamBake, thermocouples, and relay boards

Electrolux EOD6P and EOF6P series ovens, along with their AEG SteamBake and SteamCrisp counterparts, share a common electronic platform with digital temperature control, a steam generator, and an electromechanical door lock for pyrolysis mode. The most frequent issue is thermocouple drift: over time the K-type thermocouple loses accuracy and the oven begins to overheat or underheat the cavity by 20–40 degrees. We replace the thermocouple with a factory-calibrated unit and verify the readings with a digital thermometer placed directly inside the oven cavity.

The second typical fault is a stuck relay on the control board. The relay switches a 2–3 kW heating element, and under constant heating cycles the internal contacts weld together. The result is that the heating element will not turn off, the oven overheats, and the safety thermostat trips. We resolder the relay, inspect the board traces for burn damage, and restore any compromised sections. The SteamBake steam generator is a separate topic: calcium from Riga tap water clogs the generator channels within 2–3 years and steam stops reaching the cavity. We fully disassemble the generator, remove scale using ultrasonic cleaning, or replace the unit entirely if the channels are irreversibly blocked.

Induction cooktop IGBT repair and ceramic glass replacement

Electrolux EHI and AEG MaxiSense induction cooktops work by generating a high-frequency electromagnetic field through IGBT transistors. Each heating zone has its own IGBT module, resonant capacitor, and driver board. When a mains voltage spike occurs or ventilation is blocked causing overheating, the IGBT transistor fails: the zone clicks on activation, the indicator shows power, but the cookware does not heat. We diagnose each zone individually, replace the blown IGBT, check the resonant capacitor (which often fails simultaneously), and load-test the hob with real cookware.

A separate area of work is cracked ceramic glass replacement. The glass on induction and ceramic hobs cracks from point impact, uneven heating, or thermal shock. Using a hob with cracked glass is categorically unsafe — moisture penetrates to the electronics and can cause a short circuit. We order the glass by exact model article number from a verified supplier, fully disassemble the hob, install the new glass with the factory seal, and verify the unit is watertight. The entire process takes 5–10 working days depending on glass availability in stock.

Pricing & warranty

Fast on-site diagnostics. Warranty: 3 months.

If the repair cost changes during the process, the technician will call to agree on the new price. No work is done without your consent.

Frequently asked questions

Why customers choose SATER

  • Dedicated specialist per category. Your device is repaired by an engineer who only handles this device category — never others.
  • 30+ years of experience. The service centre has been operating since 1993.
  • On-site diagnostics. Diagnostics are free even if you decide not to proceed with the repair.
  • Custom-built batteries. We don't just replace batteries — we build custom packs from SONY, MOLICEL, SAMSUNG, LG and PANASONIC cells.
  • We serve all of Latvia. Our service centre is in Riga and we accept devices from anywhere in the country.